ui_test 0.7.0

A test framework for testing rustc diagnostics output
Documentation

A smaller version of compiletest-rs

Magic behavior

  • Tests are run in order of their filenames (files first, then recursing into folders). So if you have any slow tests, prepend them with a small integral number to make them get run first, taking advantage of parallelism as much as possible (instead of waiting for the slow tests at the end).

Supported magic comment annotations

If your test tests for failure, you need to add a //~ annotation where the error is happening to make sure that the test will always keep failing with a specific message at the annotated line.

//~ ERROR: XXX make sure the stderr output contains XXX for an error in the line where this comment is written

  • Also supports HELP, WARN or NOTE for different kind of message
    • if one of those levels is specified explicitly, all diagnostics of this level or higher need an annotation. If you want to avoid this, just leave out the all caps level note entirely.
  • If the all caps note is left out, a message of any level is matched. Leaving it out is not allowed for ERROR levels.
  • This checks the output before normalization, so you can check things that get normalized away, but need to be careful not to accidentally have a pattern that differs between platforms.
  • if XXX is of the form /XXX/ it is treated as a regex instead of a substring and will succeed if the regex matches.

In order to change how a single test is tested, you can add various //@ comments to the test. Any other comments will be ignored, and all //@ comments must be formatted precisely as their command specifies, or the test will fail without even being run.

  • //@ignore-C avoids running the test when condition C is met.
    • C can be target-XXX, which checks whether the target triple contains XXX.
    • C can also be one of 64bit, 32bit or 16bit.
    • C can also be on-host, which will only run the test during cross compilation testing.
  • //@only-C only runs the test when condition C is met. The conditions are the same as with ignore.
  • //@needs-asm-support only runs the test when the target supports asm!.
  • //@stderr-per-bitwidth produces one stderr file per bitwidth, as they may differ significantly sometimes
  • //@error-pattern: XXX makes sure the stderr output contains XXX
  • //@revisions: XXX YYY runs the test once for each space separated name in the list
    • emits one stderr file per revision
    • //~ comments can be restricted to specific revisions by adding the revision name after the ~ in square brackets: //~[XXX]
    • //@ comments can be restricted to specific revisions by adding the revision name after the @ in square brackets: //@[XXX]
      • Note that you cannot add revisions to the revisions command.
  • //@compile-flags: XXX appends XXX to the command line arguments passed to the rustc driver
    • you can specify this multiple times, and all the flags will accumulate
  • //@rustc-env: XXX=YYY sets the env var XXX to YYY for the rustc driver execution.
    • for Miri these env vars are used during compilation via rustc and during the emulation of the program
    • you can specify this multiple times, accumulating all the env vars
  • //@normalize-stderr-test: "REGEX" -> "REPLACEMENT" replaces all matches of REGEX in the stderr with REPLACEMENT. The replacement may specify $1 and similar backreferences to paste captures.
    • you can specify multiple such commands, there is no need to create a single regex that handles multiple replacements that you want to perform.
  • //@require-annotations-for-level: LEVEL can be used to change the level of diagnostics that require a corresponding annotation.
    • this is only useful if there are any annotations like HELP, WARN or NOTE, as these would automatically require annotations for all other diagnostics of the same or higher level.
  • //@check-pass overrides the Config::mode and will make the test behave as if the test suite were in Mode::Pass.
  • //@edition: EDITION overwrites the default edition (2021) to the given edition.
  • //@run-rustfix runs rustfix on the output and recompiles the result. The result must suceed to compile.
  • //@aux-build: filename looks for a file in the auxiliary directory (within the directory of the test), compiles it as a library and links the current crate against it. This allows you import the crate with extern crate or just via use statements.
    • you can optionally specify a crate type via //@aux-build: filename.rs:proc-macro. This is necessary for some crates (like proc macros), but can also be used to change the linkage against the aux build.
  • //@run compiles the test and runs the resulting binary. The resulting binary must exit successfully. Stdout and stderr are taken from the resulting binary. Any warnings during compilation are ignored.
    • You can also specify a different exit code/status that is expected via e.g. //@run: 1 or //@run: 101 (the latter is the standard Rust exit code for panics).

Significant differences to compiletest-rs

  • ignore-target-* and only-target-* operate solely on the triple, instead of supporting things like macos
  • only //~ comments can be individualized per revision
  • only supports ui tests
  • tests are run in named order, so you can prefix slow tests with 0 in order to make them get run first