Enum criterion::BatchSize

pub enum BatchSize {
    SmallInput,
    LargeInput,
    PerIteration,
    NumBatches(u64),
    NumIterations(u64),
    // some variants omitted
}

Argument to Bencher::iter_batched and Bencher::iter_batched_ref which controls the batch size.

Generally speaking, almost all benchmarks should use SmallInput. If the input or the result of the benchmark routine is large enough that SmallInput causes out-of-memory errors, LargeInput can be used to reduce memory usage at the cost of increasing the measurement overhead. If the input or the result is extremely large (or if it holds some limited external resource like a file handle), PerIteration will set the number of iterations per batch to exactly one. PerIteration can increase the measurement overhead substantially and should be avoided wherever possible.

Each value lists an estimate of the measurement overhead. This is intended as a rough guide to assist in choosing an option, it should not be relied upon. In particular, it is not valid to subtract the listed overhead from the measurement and assume that the result represents the true runtime of a function. The actual measurement overhead for your specific benchmark depends on the details of the function you’re benchmarking and the hardware and operating system running the benchmark.

With that said, if the runtime of your function is small relative to the measurement overhead it will be difficult to take accurate measurements. In this situation, the best option is to use Bencher::iter which has next-to-zero measurement overhead.

Variants

SmallInput

SmallInput indicates that the input to the benchmark routine (the value returned from the setup routine) is small enough that millions of values can be safely held in memory. Always prefer SmallInput unless the benchmark is using too much memory.

In testing, the maximum measurement overhead from benchmarking with SmallInput is on the order of 500 picoseconds. This is presented as a rough guide; your results may vary.

LargeInput

LargeInput indicates that the input to the benchmark routine or the value returned from that routine is large. This will reduce the memory usage but increase the measurement overhead.

In testing, the maximum measurement overhead from benchmarking with LargeInput is on the order of 750 picoseconds. This is presented as a rough guide; your results may vary.

PerIteration

PerIteration indicates that the input to the benchmark routine or the value returned from that routine is extremely large or holds some limited resource, such that holding many values in memory at once is infeasible. This provides the worst measurement overhead, but the lowest memory usage.

In testing, the maximum measurement overhead from benchmarking with PerIteration is on the order of 350 nanoseconds or 350,000 picoseconds. This is presented as a rough guide; your results may vary.

NumBatches(u64)

NumBatches will attempt to divide the iterations up into a given number of batches. A larger number of batches (and thus smaller batches) will reduce memory usage but increase measurement overhead. This allows the user to choose their own tradeoff between memory usage and measurement overhead, but care must be taken in tuning the number of batches. Most benchmarks should use SmallInput or LargeInput instead.

NumIterations(u64)

NumIterations fixes the batch size to a constant number, specified by the user. This allows the user to choose their own tradeoff between overhead and memory usage, but care must be taken in tuning the batch size. In general, the measurement overhead of NumIterations will be larger than that of NumBatches. Most benchmarks should use SmallInput or LargeInput instead.

Trait Implementations

impl Clone for BatchSize

fn clone(&self) -> BatchSize

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for BatchSize

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Hash for BatchSize

fn hash<__H: Hasher>(&self, state: &mut __H)

Feeds this value into the given Hasher.

fn hash_slice<H>(data: &[Self], state: &mut H)

where H: Hasher, Self: Sized,

Feeds a slice of this type into the given Hasher.

impl PartialEq for BatchSize

fn eq(&self, other: &BatchSize) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for BatchSize

impl Eq for BatchSize

impl StructuralPartialEq for BatchSize