Module esp32c2_hal::pac::uart0::int_raw

Raw interrupt status

Structs

INT_RAW_SPEC

Raw interrupt status

R

Register INT_RAW reader

Type Definitions

AT_CMD_CHAR_DET_INT_RAW_R

Field AT_CMD_CHAR_DET_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects the configured at_cmd char.

BRK_DET_INT_RAW_R

Field BRK_DET_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects a 0 after the stop bit.

CTS_CHG_INT_RAW_R

Field CTS_CHG_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects the edge change of CTSn signal.

DSR_CHG_INT_RAW_R

Field DSR_CHG_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects the edge change of DSRn signal.

FRM_ERR_INT_RAW_R

Field FRM_ERR_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects a data frame error .

GLITCH_DET_INT_RAW_R

Field GLITCH_DET_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects a glitch in the middle of a start bit.

PARITY_ERR_INT_RAW_R

Field PARITY_ERR_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects a parity error in the data.

RS485_CLASH_INT_RAW_R

Field RS485_CLASH_INT_RAW reader - This interrupt raw bit turns to high level when detects a clash between transmitter and receiver in rs485 mode.

RS485_FRM_ERR_INT_RAW_R

Field RS485_FRM_ERR_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects a data frame error from the echo of transmitter in rs485 mode.

RS485_PARITY_ERR_INT_RAW_R

Field RS485_PARITY_ERR_INT_RAW reader - This interrupt raw bit turns to high level when receiver detects a parity error from the echo of transmitter in rs485 mode.

RXFIFO_FULL_INT_RAW_R

Field RXFIFO_FULL_INT_RAW reader - This interrupt raw bit turns to high level when receiver receives more data than what rxfifo_full_thrhd specifies.

RXFIFO_OVF_INT_RAW_R

Field RXFIFO_OVF_INT_RAW reader - This interrupt raw bit turns to high level when receiver receives more data than the FIFO can store.

RXFIFO_TOUT_INT_RAW_R

Field RXFIFO_TOUT_INT_RAW reader - This interrupt raw bit turns to high level when receiver takes more time than rx_tout_thrhd to receive a byte.

SW_XOFF_INT_RAW_R

Field SW_XOFF_INT_RAW reader - This interrupt raw bit turns to high level when receiver receives Xoff char when uart_sw_flow_con_en is set to 1.

SW_XON_INT_RAW_R

Field SW_XON_INT_RAW reader - This interrupt raw bit turns to high level when receiver recevies Xon char when uart_sw_flow_con_en is set to 1.

TXFIFO_EMPTY_INT_RAW_R

Field TXFIFO_EMPTY_INT_RAW reader - This interrupt raw bit turns to high level when the amount of data in Tx-FIFO is less than what txfifo_empty_thrhd specifies .

TX_BRK_DONE_INT_RAW_R

Field TX_BRK_DONE_INT_RAW reader - This interrupt raw bit turns to high level when transmitter completes sending NULL characters, after all data in Tx-FIFO are sent.

TX_BRK_IDLE_DONE_INT_RAW_R

Field TX_BRK_IDLE_DONE_INT_RAW reader - This interrupt raw bit turns to high level when transmitter has kept the shortest duration after sending the last data.

TX_DONE_INT_RAW_R

Field TX_DONE_INT_RAW reader - This interrupt raw bit turns to high level when transmitter has send out all data in FIFO.

WAKEUP_INT_RAW_R

Field WAKEUP_INT_RAW reader - This interrupt raw bit turns to high level when input rxd edge changes more times than what reg_active_threshold specifies in light sleeping mode.