Trait esp32c2_hal::i2c::Instance

source · 
pub trait Instance {

Show 22 methods    fn register_block(&self) -> &RegisterBlock;
    fn i2c_number(&self) -> usize;

    fn setup(
        &mut self,
        frequency: Rate<u32, 1, 1>,
        clocks: &Clocks
    ) -> Result<(), SetupError> { ... }
    fn reset(&self) { ... }
    fn reset_command_list(&self) { ... }
    fn set_filter(&mut self, sda_threshold: Option<u8>, scl_threshold: Option<u8>) { ... }
    fn set_frequency(
        &mut self,
        source_clk: Rate<u32, 1, 1>,
        bus_freq: Rate<u32, 1, 1>
    ) -> Result<(), SetupError> { ... }
    fn configure_clock(
        &mut self,
        sclk_div: u32,
        scl_low_period: u32,
        scl_high_period: u32,
        scl_wait_high_period: u32,
        sda_hold_time: u32,
        sda_sample_time: u32,
        scl_rstart_setup_time: u32,
        scl_stop_setup_time: u32,
        scl_start_hold_time: u32,
        scl_stop_hold_time: u32,
        time_out_value: u32,
        time_out_en: bool
    ) { ... }
    fn perform_write<'a, I>(
        &self,
        addr: u8,
        bytes: &[u8],
        cmd_iterator: &mut I
    ) -> Result<(), Error>
    where
        I: Iterator<Item = &'a Reg<COMD_SPEC>>,
    { ... }
    fn perform_read<'a, I>(
        &self,
        addr: u8,
        buffer: &mut [u8],
        cmd_iterator: &mut I
    ) -> Result<(), Error>
    where
        I: Iterator<Item = &'a Reg<COMD_SPEC>>,
    { ... }
    fn read_all_from_fifo(&self, buffer: &mut [u8]) -> Result<(), Error> { ... }
    fn clear_all_interrupts(&self) { ... }
    fn wait_for_completion(&self) -> Result<(), Error> { ... }
    fn check_errors(&self) -> Result<(), Error> { ... }
    fn update_config(&self) { ... }
    fn start_transmission(&self) { ... }
    fn fill_tx_fifo(&self, bytes: &[u8]) -> usize { ... }
    fn write_remaining_tx_fifo(
        &self,
        start_index: usize,
        bytes: &[u8]
    ) -> Result<(), Error> { ... }
    fn reset_fifo(&self) { ... }
    fn master_write(&mut self, addr: u8, bytes: &[u8]) -> Result<(), Error> { ... }
    fn master_read(&mut self, addr: u8, buffer: &mut [u8]) -> Result<(), Error> { ... }
    fn master_write_read(
        &mut self,
        addr: u8,
        bytes: &[u8],
        buffer: &mut [u8]
    ) -> Result<(), Error> { ... }

}
Expand description

I2C Peripheral Instance

Required Methods

Provided Methods

Resets the I2C controller (FIFO + FSM + command list)

Resets the I2C peripheral’s command registers

Sets the filter with a supplied threshold in clock cycles for which a pulse must be present to pass the filter

Sets the frequency of the I2C interface by calculating and applying the associated timings - corresponds to i2c_ll_cal_bus_clk and i2c_ll_set_bus_timing in ESP-IDF

Resets the transmit and receive FIFO buffers

Send data bytes from the bytes array to a target slave with the address addr

Read bytes from a target slave with the address addr The number of read bytes is deterimed by the size of the buffer argument

Write bytes from the bytes array first and then read n bytes into the buffer array with n being the size of the array.

Implementors