Struct stm32_metapac::sai::regs::Cr2

#[repr(transparent)]
pub struct Cr2(pub u32);

Configuration register 2

Tuple Fields

0: u32

Implementations

impl Cr2

pub const fn fth(&self) -> Fth

FIFO threshold. This bit is set and cleared by software.

pub fn set_fth(&mut self, val: Fth)

FIFO threshold. This bit is set and cleared by software.

pub const fn fflush(&self) -> bool

FIFO flush. This bit is set by software. It is always read as 0. This bit should be configured when the SAI is disabled.

pub fn set_fflush(&mut self, val: bool)

FIFO flush. This bit is set by software. It is always read as 0. This bit should be configured when the SAI is disabled.

pub const fn tris(&self) -> bool

Tristate management on data line. This bit is set and cleared by software. It is meaningful only if the audio block is configured as a transmitter. This bit is not used when the audio block is configured in SPDIF mode. It should be configured when SAI is disabled. Refer to Section: Output data line management on an inactive slot for more details.

pub fn set_tris(&mut self, val: bool)

Tristate management on data line. This bit is set and cleared by software. It is meaningful only if the audio block is configured as a transmitter. This bit is not used when the audio block is configured in SPDIF mode. It should be configured when SAI is disabled. Refer to Section: Output data line management on an inactive slot for more details.

pub const fn mute(&self) -> bool

Mute. This bit is set and cleared by software. It is meaningful only when the audio block operates as a transmitter. The MUTE value is linked to value of MUTEVAL if the number of slots is lower or equal to 2, or equal to 0 if it is greater than 2. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.

pub fn set_mute(&mut self, val: bool)

Mute. This bit is set and cleared by software. It is meaningful only when the audio block operates as a transmitter. The MUTE value is linked to value of MUTEVAL if the number of slots is lower or equal to 2, or equal to 0 if it is greater than 2. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.

pub const fn muteval(&self) -> Muteval

Mute value. This bit is set and cleared by software.It must be written before enabling the audio block: SAIXEN. This bit is meaningful only when the audio block operates as a transmitter, the number of slots is lower or equal to 2 and the MUTE bit is set. If more slots are declared, the bit value sent during the transmission in mute mode is equal to 0, whatever the value of MUTEVAL. if the number of slot is lower or equal to 2 and MUTEVAL = 1, the MUTE value transmitted for each slot is the one sent during the previous frame. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.

pub fn set_muteval(&mut self, val: Muteval)

Mute value. This bit is set and cleared by software.It must be written before enabling the audio block: SAIXEN. This bit is meaningful only when the audio block operates as a transmitter, the number of slots is lower or equal to 2 and the MUTE bit is set. If more slots are declared, the bit value sent during the transmission in mute mode is equal to 0, whatever the value of MUTEVAL. if the number of slot is lower or equal to 2 and MUTEVAL = 1, the MUTE value transmitted for each slot is the one sent during the previous frame. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.

pub const fn mutecnt(&self) -> u8

Mute counter. These bits are set and cleared by software. They are used only in reception mode. The value set in these bits is compared to the number of consecutive mute frames detected in reception. When the number of mute frames is equal to this value, the flag MUTEDET will be set and an interrupt will be generated if bit MUTEDETIE is set. Refer to Section: Mute mode for more details.

pub fn set_mutecnt(&mut self, val: u8)

Mute counter. These bits are set and cleared by software. They are used only in reception mode. The value set in these bits is compared to the number of consecutive mute frames detected in reception. When the number of mute frames is equal to this value, the flag MUTEDET will be set and an interrupt will be generated if bit MUTEDETIE is set. Refer to Section: Mute mode for more details.

pub const fn cpl(&self) -> Cpl

Complement bit. This bit is set and cleared by software. It defines the type of complement to be used for companding mode Note: This bit has effect only when the companding mode is -Law algorithm or A-Law algorithm.

pub fn set_cpl(&mut self, val: Cpl)

Complement bit. This bit is set and cleared by software. It defines the type of complement to be used for companding mode Note: This bit has effect only when the companding mode is -Law algorithm or A-Law algorithm.

pub const fn comp(&self) -> Comp

Companding mode. These bits are set and cleared by software. The -Law and the A-Law log are a part of the CCITT G.711 recommendation, the type of complement that will be used depends on CPL bit. The data expansion or data compression are determined by the state of bit MODE[0]. The data compression is applied if the audio block is configured as a transmitter. The data expansion is automatically applied when the audio block is configured as a receiver. Refer to Section: Companding mode for more details. Note: Companding mode is applicable only when TDM is selected.

pub fn set_comp(&mut self, val: Comp)

Companding mode. These bits are set and cleared by software. The -Law and the A-Law log are a part of the CCITT G.711 recommendation, the type of complement that will be used depends on CPL bit. The data expansion or data compression are determined by the state of bit MODE[0]. The data compression is applied if the audio block is configured as a transmitter. The data expansion is automatically applied when the audio block is configured as a receiver. Refer to Section: Companding mode for more details. Note: Companding mode is applicable only when TDM is selected.

Trait Implementations

impl Clone for Cr2

fn clone(&self) -> Cr2

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Cr2

fn default() -> Cr2

Returns the “default value” for a type.

impl PartialEq for Cr2

fn eq(&self, other: &Cr2) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Cr2

impl Eq for Cr2

impl StructuralEq for Cr2

impl StructuralPartialEq for Cr2