Struct stm32_metapac::usart::regs::Cr2

#[repr(transparent)]
pub struct Cr2(pub u32);

Control register 2

Tuple Fields

0: u32

Implementations

impl Cr2

pub const fn addm(&self) -> Addm

7-bit Address Detection/4-bit Address Detection

pub fn set_addm(&mut self, val: Addm)

7-bit Address Detection/4-bit Address Detection

pub const fn lbdl(&self) -> Lbdl

Line break detection length

pub fn set_lbdl(&mut self, val: Lbdl)

Line break detection length

pub const fn lbdie(&self) -> bool

LIN break detection interrupt enable

pub fn set_lbdie(&mut self, val: bool)

LIN break detection interrupt enable

pub const fn lbcl(&self) -> bool

Last bit clock pulse

pub fn set_lbcl(&mut self, val: bool)

Last bit clock pulse

pub const fn cpha(&self) -> Cpha

Clock phase

pub fn set_cpha(&mut self, val: Cpha)

Clock phase

pub const fn cpol(&self) -> Cpol

Clock polarity

pub fn set_cpol(&mut self, val: Cpol)

Clock polarity

pub const fn clken(&self) -> bool

Clock enable

pub fn set_clken(&mut self, val: bool)

Clock enable

pub const fn stop(&self) -> Stop

STOP bits

pub fn set_stop(&mut self, val: Stop)

STOP bits

pub const fn linen(&self) -> bool

LIN mode enable

pub fn set_linen(&mut self, val: bool)

LIN mode enable

pub const fn swap(&self) -> bool

Swap TX/RX pins

pub fn set_swap(&mut self, val: bool)

Swap TX/RX pins

pub const fn rxinv(&self) -> bool

RX pin active level inversion

pub fn set_rxinv(&mut self, val: bool)

RX pin active level inversion

pub const fn txinv(&self) -> bool

TX pin active level inversion

pub fn set_txinv(&mut self, val: bool)

TX pin active level inversion

pub const fn datainv(&self) -> bool

Binary data inversion

pub fn set_datainv(&mut self, val: bool)

Binary data inversion

pub const fn msbfirst(&self) -> Msbfirst

Most significant bit first

pub fn set_msbfirst(&mut self, val: Msbfirst)

Most significant bit first

pub const fn abren(&self) -> bool

Auto baud rate enable

pub fn set_abren(&mut self, val: bool)

Auto baud rate enable

pub const fn abrmod(&self) -> Abrmod

Auto baud rate mode

pub fn set_abrmod(&mut self, val: Abrmod)

Auto baud rate mode

pub const fn rtoen(&self) -> bool

Receiver timeout enable

pub fn set_rtoen(&mut self, val: bool)

Receiver timeout enable

pub const fn add(&self) -> u8

Address of the USART node

pub fn set_add(&mut self, val: u8)

Address of the USART node

Trait Implementations

impl Clone for Cr2

fn clone(&self) -> Cr2

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Cr2

fn default() -> Cr2

Returns the “default value” for a type.

impl PartialEq for Cr2

fn eq(&self, other: &Cr2) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Cr2

impl Eq for Cr2

impl StructuralEq for Cr2

impl StructuralPartialEq for Cr2