Enum RequestType

pub enum RequestType {
    Bridge {
        network: String,
        access_token: String,
        security: StreamSecurity,
    },
    Flush,
    Unbridge,
    DhcpAcquire,
    IpAdd {
        ip: IpAddr,
        prefix: u8,
    },
    IpRemove(IpAddr),
    IpClear,
    GetIpList,
    GetMac,
    GatewaySet(IpAddr),
    RouteAdd {
        cidr: IpCidr,
        via_router: IpAddr,
        preferred_until: Option<Duration>,
        expires_at: Option<Duration>,
    },
    RouteRemove(IpAddr),
    RouteClear,
    GetRouteList,
    BindRaw(SocketId),
    ListenTcp {
        socket_id: SocketId,
        addr: SocketAddr,
        only_v6: bool,
        reuse_port: bool,
        reuse_addr: bool,
    },
    BindUdp {
        socket_id: SocketId,
        addr: SocketAddr,
        reuse_port: bool,
        reuse_addr: bool,
    },
    BindIcmp {
        socket_id: SocketId,
        addr: IpAddr,
    },
    ConnectTcp {
        socket_id: SocketId,
        addr: SocketAddr,
        peer: SocketAddr,
    },
    Resolve {
        host: String,
        port: Option<u16>,
        dns_server: Option<IpAddr>,
    },
    Close,
    BeginAccept(SocketId),
    GetAddrLocal,
    GetAddrPeer,
    SetTtl(u32),
    GetTtl,
    GetStatus,
    SetLinger(Option<Duration>),
    GetLinger,
    SetPromiscuous(bool),
    GetPromiscuous,
    SetRecvBufSize(u64),
    GetRecvBufSize,
    SetSendBufSize(u64),
    GetSendBufSize,
    SetNoDelay(bool),
    GetNoDelay,
    SetKeepAlive(bool),
    GetKeepAlive,
    SetDontRoute(bool),
    GetDontRoute,
    Shutdown(Shutdown),
    IsClosed,
    SetBroadcast(bool),
    GetBroadcast,
    SetMulticastLoopV4(bool),
    GetMulticastLoopV4,
    SetMulticastLoopV6(bool),
    GetMulticastLoopV6,
    SetMulticastTtlV4(u32),
    GetMulticastTtlV4,
    JoinMulticastV4 {
        multiaddr: Ipv4Addr,
        iface: Ipv4Addr,
    },
    LeaveMulticastV4 {
        multiaddr: Ipv4Addr,
        iface: Ipv4Addr,
    },
    JoinMulticastV6 {
        multiaddr: Ipv6Addr,
        iface: u32,
    },
    LeaveMulticastV6 {
        multiaddr: Ipv6Addr,
        iface: u32,
    },
}

Variants

Bridge

Bridges this local network with a remote network, which is required in order to make lower level networking calls (such as UDP/TCP)

Fields

network: String

access_token: String

security: StreamSecurity

Flush

Flushes all the data by ensuring a full round trip is completed

Unbridge

Disconnects from the remote network essentially unbridging it

DhcpAcquire

Acquires an IP address on the network and configures the routing tables

IpAdd

Adds a static IP address to the interface with a netmask prefix

Fields

ip: IpAddr

prefix: u8

IpRemove(IpAddr)

Removes a static (or dynamic) IP address from the interface

IpClear

Clears all the assigned IP addresses for this interface

GetIpList

Lists all the IP addresses currently assigned to this interface

GetMac

Returns the hardware MAC address for this interface

GatewaySet(IpAddr)

Adds a default gateway to the routing table

RouteAdd

Adds a specific route to the routing table

Fields

cidr: IpCidr

via_router: IpAddr

preferred_until: Option<Duration>

expires_at: Option<Duration>

RouteRemove(IpAddr)

Removes a routing rule from the routing table

RouteClear

Clears the routing table for this interface

GetRouteList

Lists all the routes defined in the routing table for this interface

BindRaw(SocketId)

Creates a low level socket that can read and write Ethernet packets directly to the interface

ListenTcp

Lists for TCP connections on a specific IP and Port combination Multiple servers (processes or threads) can bind to the same port if they each set the reuse-port and-or reuse-addr flags

Fields

socket_id: SocketId

addr: SocketAddr

only_v6: bool

reuse_port: bool

reuse_addr: bool

BindUdp

Opens a UDP socket that listens on a specific IP and Port combination Multiple servers (processes or threads) can bind to the same port if they each set the reuse-port and-or reuse-addr flags

Fields

socket_id: SocketId

addr: SocketAddr

reuse_port: bool

reuse_addr: bool

BindIcmp

Creates a socket that can be used to send and receive ICMP packets from a paritcular IP address

Fields

socket_id: SocketId

addr: IpAddr

ConnectTcp

Opens a TCP connection to a particular destination IP address and port

Fields

socket_id: SocketId

addr: SocketAddr

peer: SocketAddr

Resolve

Performs DNS resolution for a specific hostname

Fields

host: String

port: Option<u16>

dns_server: Option<IpAddr>

Close

Closes the socket

BeginAccept(SocketId)

Begins the process of accepting a socket and returns it later

GetAddrLocal

Returns the local address of this TCP listener

GetAddrPeer

Returns the address (IP and Port) of the peer socket that this is conencted to

SetTtl(u32)

Sets how many network hops the packets are permitted for new connections

GetTtl

Returns the maximum number of network hops before packets are dropped

GetStatus

Returns the status/state of the socket

SetLinger(Option<Duration>)

Determines how long the socket will remain in a TIME_WAIT after it disconnects (only the one that initiates the close will be in a TIME_WAIT state thus the clients should always do this rather than the server)

GetLinger

Returns how long the socket will remain in a TIME_WAIT after it disconnects

SetPromiscuous(bool)

Tells the raw socket and its backing switch that all packets should be received by this socket even if they are not destined for this device

GetPromiscuous

Returns if the socket is running in promiscuous mode whereby it will receive all packets even if they are not destined for the local interface

SetRecvBufSize(u64)

Sets the receive buffer size which acts as a trottle for how much data is buffered on this side of the pipe

GetRecvBufSize

Size of the receive buffer that holds all data that has not yet been read

SetSendBufSize(u64)

Sets the size of the send buffer which will hold the bytes of data while they are being sent over to the peer

GetSendBufSize

Size of the send buffer that holds all data that is currently being transmitted.

SetNoDelay(bool)

When NO_DELAY is set the data that needs to be transmitted to the peer is sent immediately rather than waiting for a bigger batch of data, this reduces latency but increases encapsulation overhead.

GetNoDelay

Indicates if the NO_DELAY flag is set which means that data is immediately sent to the peer without waiting. This reduces latency but increases encapsulation overhead.

SetKeepAlive(bool)

When KEEP_ALIVE is set the connection will periodically send an empty data packet to the server to make sure the connection stays alive.

GetKeepAlive

Indicates if the KEEP_ALIVE flag is set which means that the socket will periodically send an empty data packet to keep the connection alive.

SetDontRoute(bool)

When DONT_ROUTE is set the packet will be sent directly to the interface without passing through the routing logic.

GetDontRoute

Indicates if the packet will pass straight through to the interface bypassing the routing logic.

Shutdown(Shutdown)

Shuts down either the READER or WRITER sides of the socket connection.

IsClosed

Return true if the socket is closed

SetBroadcast(bool)

Sets a flag that means that the UDP socket is able to receive and process broadcast packets.

GetBroadcast

Indicates if the SO_BROADCAST flag is set which means that the UDP socket will receive and process broadcast packets

SetMulticastLoopV4(bool)

Sets a flag that indicates if multicast packets that this socket is a member of will be looped back to the sending socket. This applies to IPv4 addresses

GetMulticastLoopV4

Gets a flag that indicates if multicast packets that this socket is a member of will be looped back to the sending socket. This applies to IPv4 addresses

SetMulticastLoopV6(bool)

Sets a flag that indicates if multicast packets that this socket is a member of will be looped back to the sending socket. This applies to IPv6 addresses

GetMulticastLoopV6

Gets a flag that indicates if multicast packets that this socket is a member of will be looped back to the sending socket. This applies to IPv6 addresses

SetMulticastTtlV4(u32)

Sets the TTL for IPv4 multicast packets which is the number of network hops before the packet is dropped

GetMulticastTtlV4

Gets the TTL for IPv4 multicast packets which is the number of network hops before the packet is dropped

JoinMulticastV4

Tells this interface that it will subscribe to a particular multicast address. This applies to IPv4 addresses

Fields

multiaddr: Ipv4Addr

iface: Ipv4Addr

LeaveMulticastV4

Tells this interface that it will unsubscribe to a particular multicast address. This applies to IPv4 addresses

Fields

multiaddr: Ipv4Addr

iface: Ipv4Addr

JoinMulticastV6

Tells this interface that it will subscribe to a particular multicast address. This applies to IPv6 addresses

Fields

multiaddr: Ipv6Addr

iface: u32

LeaveMulticastV6

Tells this interface that it will unsubscribe to a particular multicast address. This applies to IPv6 addresses

Fields

multiaddr: Ipv6Addr

iface: u32

Trait Implementations

impl Clone for RequestType

fn clone(&self) -> RequestType

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for RequestType

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl<'de> Deserialize<'de> for RequestType

fn deserialize<__D>(__deserializer: __D) -> Result<Self, __D::Error>

where __D: Deserializer<'de>,

Deserialize this value from the given Serde deserializer.

impl Serialize for RequestType

fn serialize<__S>(&self, __serializer: __S) -> Result<__S::Ok, __S::Error>

where __S: Serializer,

Serialize this value into the given Serde serializer.