#[non_exhaustive]
pub enum Event {
    Down {
        serial: u32,
        time: u32,
        surface: WlSurface,
        id: i32,
        x: f64,
        y: f64,
    },
    Up {
        serial: u32,
        time: u32,
        id: i32,
    },
    Motion {
        time: u32,
        id: i32,
        x: f64,
        y: f64,
    },
    Frame,
    Cancel,
    Shape {
        id: i32,
        major: f64,
        minor: f64,
    },
    Orientation {
        id: i32,
        orientation: f64,
    },
}

Variants (Non-exhaustive)

This enum is marked as non-exhaustive
Non-exhaustive enums could have additional variants added in future. Therefore, when matching against variants of non-exhaustive enums, an extra wildcard arm must be added to account for any future variants.

Down

Fields

serial: u32
time: u32
surface: WlSurface
id: i32
x: f64
y: f64

touch down event and beginning of a touch sequence

A new touch point has appeared on the surface. This touch point is assigned a unique ID. Future events from this touch point reference this ID. The ID ceases to be valid after a touch up event and may be reused in the future.

Up

Fields

serial: u32
time: u32
id: i32

end of a touch event sequence

The touch point has disappeared. No further events will be sent for this touch point and the touch point’s ID is released and may be reused in a future touch down event.

Motion

Fields

time: u32
id: i32
x: f64
y: f64

update of touch point coordinates

A touch point has changed coordinates.

Frame

end of touch frame event

Indicates the end of a set of events that logically belong together. A client is expected to accumulate the data in all events within the frame before proceeding.

A wl_touch.frame terminates at least one event but otherwise no guarantee is provided about the set of events within a frame. A client must assume that any state not updated in a frame is unchanged from the previously known state.

Cancel

touch session cancelled

Sent if the compositor decides the touch stream is a global gesture. No further events are sent to the clients from that particular gesture. Touch cancellation applies to all touch points currently active on this client’s surface. The client is responsible for finalizing the touch points, future touch points on this surface may reuse the touch point ID.

Shape

Fields

id: i32
major: f64
minor: f64

update shape of touch point

Sent when a touchpoint has changed its shape.

This event does not occur on its own. It is sent before a wl_touch.frame event and carries the new shape information for any previously reported, or new touch points of that frame.

Other events describing the touch point such as wl_touch.down, wl_touch.motion or wl_touch.orientation may be sent within the same wl_touch.frame. A client should treat these events as a single logical touch point update. The order of wl_touch.shape, wl_touch.orientation and wl_touch.motion is not guaranteed. A wl_touch.down event is guaranteed to occur before the first wl_touch.shape event for this touch ID but both events may occur within the same wl_touch.frame.

A touchpoint shape is approximated by an ellipse through the major and minor axis length. The major axis length describes the longer diameter of the ellipse, while the minor axis length describes the shorter diameter. Major and minor are orthogonal and both are specified in surface-local coordinates. The center of the ellipse is always at the touchpoint location as reported by wl_touch.down or wl_touch.move.

This event is only sent by the compositor if the touch device supports shape reports. The client has to make reasonable assumptions about the shape if it did not receive this event.

Only available since version 6 of the interface

Orientation

Fields

id: i32
orientation: f64

update orientation of touch point

Sent when a touchpoint has changed its orientation.

This event does not occur on its own. It is sent before a wl_touch.frame event and carries the new shape information for any previously reported, or new touch points of that frame.

Other events describing the touch point such as wl_touch.down, wl_touch.motion or wl_touch.shape may be sent within the same wl_touch.frame. A client should treat these events as a single logical touch point update. The order of wl_touch.shape, wl_touch.orientation and wl_touch.motion is not guaranteed. A wl_touch.down event is guaranteed to occur before the first wl_touch.orientation event for this touch ID but both events may occur within the same wl_touch.frame.

The orientation describes the clockwise angle of a touchpoint’s major axis to the positive surface y-axis and is normalized to the -180 to +180 degree range. The granularity of orientation depends on the touch device, some devices only support binary rotation values between 0 and 90 degrees.

This event is only sent by the compositor if the touch device supports orientation reports.

Only available since version 6 of the interface

Trait Implementations

Formats the value using the given formatter. Read more

Wire representation of this MessageGroup

The wrapper type for ObjectMap allowing the mapping of Object and NewId arguments to the object map during parsing. Read more

Whether this message is a destructor Read more

The opcode of this message

The minimal object version for which this message exists

Retrieve the child Object associated with this message if any

Construct a message from its raw representation

Turn this message into its raw representation

Construct a message of this group from its C representation Read more

Build a C representation of this message Read more

Auto Trait Implementations

Blanket Implementations

Gets the TypeId of self. Read more

Immutably borrows from an owned value. Read more

Mutably borrows from an owned value. Read more

Convert Box<dyn Trait> (where Trait: Downcast) to Box<dyn Any>. Box<dyn Any> can then be further downcast into Box<ConcreteType> where ConcreteType implements Trait. Read more

Convert Rc<Trait> (where Trait: Downcast) to Rc<Any>. Rc<Any> can then be further downcast into Rc<ConcreteType> where ConcreteType implements Trait. Read more

Convert &Trait (where Trait: Downcast) to &Any. This is needed since Rust cannot generate &Any’s vtable from &Trait’s. Read more

Convert &mut Trait (where Trait: Downcast) to &Any. This is needed since Rust cannot generate &mut Any’s vtable from &mut Trait’s. Read more

Convert Arc<Trait> (where Trait: Downcast) to Arc<Any>. Arc<Any> can then be further downcast into Arc<ConcreteType> where ConcreteType implements Trait. Read more

Returns the argument unchanged.

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

The type returned in the event of a conversion error.

Performs the conversion.

The type returned in the event of a conversion error.

Performs the conversion.