Enum Event

#[non_exhaustive]
pub enum Event {
    Buttons {
        buttons: Vec<u8>,
    },
    Ring {
        ring: ZwpTabletPadRingV2,
    },
    Strip {
        strip: ZwpTabletPadStripV2,
    },
    Modes {
        modes: u32,
    },
    Done,
    ModeSwitch {
        time: u32,
        serial: u32,
        mode: u32,
    },
}

Available on crate feature client only.

Variants (Non-exhaustive)

Non-exhaustive enums could have additional variants added in future. Therefore, when matching against variants of non-exhaustive enums, an extra wildcard arm must be added to account for any future variants.

Buttons

buttons announced

Sent on wp_tablet_pad_group initialization to announce the available buttons in the group. Button indices start at 0, a button may only be in one group at a time.

This event is first sent in the initial burst of events before the wp_tablet_pad_group.done event.

Some buttons are reserved by the compositor. These buttons may not be assigned to any wp_tablet_pad_group. Compositors may broadcast this event in the case of changes to the mapping of these reserved buttons. If the compositor happens to reserve all buttons in a group, this event will be sent with an empty array.

Fields

buttons: Vec<u8>

buttons in this group

Ring

ring announced

Sent on wp_tablet_pad_group initialization to announce available rings. One event is sent for each ring available on this pad group.

This event is sent in the initial burst of events before the wp_tablet_pad_group.done event.

Fields

ring: ZwpTabletPadRingV2

Strip

strip announced

Sent on wp_tablet_pad initialization to announce available strips. One event is sent for each strip available on this pad group.

This event is sent in the initial burst of events before the wp_tablet_pad_group.done event.

Fields

strip: ZwpTabletPadStripV2

Modes

mode-switch ability announced

Sent on wp_tablet_pad_group initialization to announce that the pad group may switch between modes. A client may use a mode to store a specific configuration for buttons, rings and strips and use the wl_tablet_pad_group.mode_switch event to toggle between these configurations. Mode indices start at 0.

Switching modes is compositor-dependent. See the wp_tablet_pad_group.mode_switch event for more details.

This event is sent in the initial burst of events before the wp_tablet_pad_group.done event. This event is only sent when more than more than one mode is available.

Fields

modes: u32

the number of modes

Done

tablet group description events sequence complete

This event is sent immediately to signal the end of the initial burst of descriptive events. A client may consider the static description of the tablet to be complete and finalize initialization of the tablet group.

ModeSwitch

mode switch event

Notification that the mode was switched.

A mode applies to all buttons, rings and strips in a group simultaneously, but a client is not required to assign different actions for each mode. For example, a client may have mode-specific button mappings but map the ring to vertical scrolling in all modes. Mode indices start at 0.

Switching modes is compositor-dependent. The compositor may provide visual cues to the client about the mode, e.g. by toggling LEDs on the tablet device. Mode-switching may be software-controlled or controlled by one or more physical buttons. For example, on a Wacom Intuos Pro, the button inside the ring may be assigned to switch between modes.

The compositor will also send this event after wp_tablet_pad.enter on each group in order to notify of the current mode. Groups that only feature one mode will use mode=0 when emitting this event.

If a button action in the new mode differs from the action in the previous mode, the client should immediately issue a wp_tablet_pad.set_feedback request for each changed button.

If a ring or strip action in the new mode differs from the action in the previous mode, the client should immediately issue a wp_tablet_ring.set_feedback or wp_tablet_strip.set_feedback request for each changed ring or strip.

Fields

time: u32

the time of the event with millisecond granularity

serial: u32

mode: u32

the new mode of the pad

Implementations

impl Event

pub fn opcode(&self) -> u16

Get the opcode number of this message

Trait Implementations

impl Debug for Event

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.